ماژول شارژر پیشرفته Fast Charge دارای پورت Type-C و دو خروجی USB
ماژول شارژر / دشارژر باتری لیتیومی دارای 2 خروجی USB با ورودی های میکرو USB و Type-C مناسب برای ساخت پاور بانک
ماژول مبدل PWM به ولتاژ 10-0 ولت
ماژول تنظیم ولتاژ با موج PWM با قابلیت تغییر دیوتی سایکل برای تغییر ولتاژ میانگین در خروجی، دارای فرکانس کاری در بازه 1 تا 3 کیلوهرتز و ولتاژ خروجی در بازه 0 تا 10 ولت
After power on, without input signal, the output is 0V, so only input can output.
The first time when the power is on, it is best to do a calibration debugging:Input a 50% duty ratio signal to PWM/GND and adjust the relative amplitude short cap. The frequency is 1KHZ-3KHZ, Measured VOUT and GND with a multimeter and it will display 5V. Adjust potentiometer to make sure display 5.00V on multimeter. This will calibrate your pulse signal to this module.
When the frequency changes, the correspondences may be offset and need to be re calibrated.
The output voltage can be adjusted by adjusting the duty ratio.
The accuracy can be controlled by adjusting the potentiometer.
he PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.
It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM. The modules are small in size and easy to use in different places.
Using single chip embedded technology;
Peak 4.5v to 10V level, jumper inserted at 5V. This level of signal mainly for conventional industrial control card (such as MACH3 board Card) 5V CPU interface;
Easy to operate, can be fine-tuned by potentiometer;
Select the PWM signal input level range through short cap;
Module is small, easy to carry and use;
Module operating voltage: DC12V-30V (power requirements: greater than 100mA);
PWM signal reception frequency range: 1KHz-3KHz;
Peak 12 to 24V level, jumper inserted in the 24V. This level of signal is mainly aimed at the conventional PLC interface;
Conversion range: 0% -100% PWM to 0-10v voltage;
Allowable error: 5%;
MCU embedded technology
Easy to operate, fine tuned by potentiometer
Select the PWM signal input level range through short-circuit
The module is smaller, easy to carry and use
Parameters
Work Voltage:DC 12V-30V; (> 100MA)
PWM Receiver Frequency:1KHZ-3KHZ
PWM signal input level range:
The peak of 4.5V to 10V level. The short cap install in ‘5V’. This level is used for normal controller or 5V MCU
The peak of 12V to 24V level, so inserted in 24V. The short cap install in ‘24V’. This level is used for normal PLC controller
Conversion range:0%-100% PWM to 0-10V
Allowable error:5%
VCC: working power 12-30V
GND: ground
PWM: input PWM signal positive
GND: input voltage ground
VOUT: Output voltage: 0-10V
GND: output ground
ماژول شارژر پیشرفته Fast Charge دارای پورت Type-C و دو خروجی USB
ماژول شارژر / دشارژر باتری لیتیومی دارای 2 خروجی USB با ورودی های میکرو USB و Type-C مناسب برای ساخت پاور بانک
ماژول تغذیه 220 به 5 ولت با جریان 1 آمپر
ماژول افزاینده MT3608 با سوکت TYPE-C
ماژول تبدیل micro usb برد سبز
یک ماژول الکترونیکی است که برای تبدیل اتصالات میکرو یو اس بی به اتصالات دیگر استفاده می شود.
شارژر باتری 3 سل (برد سبز) 40 آمپر ورژن Enhanced
ماژول مدیریت فرآیند شارژ و دشارژ باتری لیتیومی 3 سل با جریان 40 آمپر
ماژول کاهنده DC-DC با جریان 8 آمپر مدل XL4016
ماژول کاهنده با جریان 8 آمپر توان بیشینه 200 وات محدوده ورودی 4 تا 40 ولت و خروجی 1.25 تا 36 ولت
ماژول رگولاتور کاهنده 5 ولت 3A با خروجی USB
مبدل DC به DC معماری BUCK کاهنده ولتاژ 5 ولت و حداکثر جریان خروجی 3 آمپر مناسب برای شارژ گوشی با باتری ماشین
ماژول شارژر - پاوربانک به همراه ورودی پنل خورشیدی
ماژول شارژر باتری لیتیومی با ورودی تغذیه micro USB و پنل خورشیدی
ماژول مبدل PWM به ولتاژ 10-0 ولت
i47SHOP
اولین و جامع ترین فروشگاه ماژول های کاربردی در ایران
ثبت سفارش به صورت عمده واردات مستقیم از چین
تولید و ساخت ابزار الکترونیک به صورت عمده و پروژه ای.
لطفا ابتدا وارد شوید.
ورود به سیستم
یک حساب کاربری رایگان برای ذخیره آیتمهای محبوب ایجاد کنید.
ورود به سیستمیک حساب کاربری رایگان برای استفاده از لیست علاقه مندی ها ایجاد کنید.
ورود به سیستم