شیلد درایور CNC ورژن 3

شیلد درایور CNC ورژن 3 از بردهای توسعه آردوینو بوده و به راحتی می توان روی برد آردوینو قرار داد. از شیلد درایور CNC می توان در ساخت دستگاه لیزر و برش CNC، پرینتر سه بعدی، ربات های صنعتی استفاده کرد. برای راه انداری شیلد درایور CNC از ماژول های (A4988، DRV8825) و استپرموتورهای دوقطبی یا همان چهار سیمه استفاده کرد.

Specification

Latest Arduino CNC Shield V3

GRBL 0.8c compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)

4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)

2 x End stops for each axis (6 in total)

Spindle enable and direction

Coolant enable

Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others)

Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )

Compact design.

Stepper Motors can be connected with 4 pin molex connectors or soldered in place.

Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)

Please note that this is an unassembled kit and needs soldering.

Instruction

UNO for Arduino---------------------- expansion board

8 ------------------------ EN ( stepper motor driver enable , active low )

7 ----------------------- Z.DIR (Z -axis direction control )

6 ----------------------- Y.DIR (Y -axis direction control )

5 ----------------------- X.DIR (X -axis direction control )

4 ---------------------- Z.STEP (Z -axis stepper control )

3 ---------------------- Y.STEP (Y -axis stepper control )

2 ---------------------- X.STEP (X -axis stepper control )

/ / The following is a simple stepper motor control procedures,

# define EN 8 / / stepper motor enable , active low

# define X_DIR 5 / / X -axis stepper motor direction control

# define Y_DIR 6 / / y -axis stepper motor direction control

# define Z_DIR 7 / / z axis stepper motor direction control

# define X_STP 2 / / x -axis stepper control

# define Y_STP 3 / / y -axis stepper control

# define Z_STP 4 / / z -axis stepper control

/ *

/ / Function : step . function: to control the direction of the stepper motor , the number of steps .

/ / Parameters : dir direction control , dirPin corresponding stepper motor DIR pin , stepperPin corresponding stepper motor " step " pin , Step number of step of no return value.

* /

void step (boolean dir, byte dirPin, byte stepperPin, int steps)

{

digitalWrite (dirPin, dir);

delay (50);

for (int i = 0; i <steps; i + +) {

digitalWrite (stepperPin, HIGH);

delayMicroseconds (800);

digitalWrite (stepperPin, LOW);

delayMicroseconds (800);

}

}

void setup () {/ / The stepper motor used in the IO pin is set to output

pinMode (X_DIR, OUTPUT); pinMode (X_STP, OUTPUT);

pinMode (Y_DIR, OUTPUT); pinMode (Y_STP, OUTPUT);

pinMode (Z_DIR, OUTPUT); pinMode (Z_STP, OUTPUT);

pinMode (EN, OUTPUT);

digitalWrite (EN, LOW);

}

void loop () {

step (false, X_DIR, X_STP, 200); / / X axis motor reverse 1 ring, the 200 step is a circle.

step (false, Y_DIR, Y_STP, 200); / / y axis motor reverse 1 ring, the 200 step is a circle.

step (false, Z_DIR, Z_STP, 200); / / z axis motor reverse 1 ring, the 200 step is a circle.

delay (1000);

step (true, X_DIR, X_STP, 200); / / X axis motor forward 1 laps, the 200 step is a circle.

step (true, Y_DIR, Y_STP, 200); / / y axis motor forward 1 laps, the 200 step is a circle.

step (true, Z_DIR, Z_STP, 200); / / z axis motor forward 1 laps, the 200 step is a circle.

delay (1000);

}

Note: When inserting the A4988 module, must be careful not to insert opposite. Stepper motor wiring as follows:

2A, 2B is a group (red, green), 1A, 1B is a group (blue, yellow), if want to change direction, can be change the position of one group , for example 2A, 2B mutually exchanged.